Measure and understand the performance of Infiniband under load.
Parameters of the experiments
Read operations performed by clients. Single table/object is read
over and over. More details at Workload+Generator
Cluster used - cluster hardware info is at Cluster+Configuration
rc02 - server (master)
rc03 - client (queen)
rc04-31 - client (worker) - multiple if required.
Reference Graph - Throughput of the system for 100 byte object reads using different Transmit Buffer Pool sizes
Analysis of throughput curves.
Summary - throughput drops to 50% under high load.
The throughput of the system is measured here against increasing
load. The load is in terms of read operations on 100 byte objects.
We notice that the throughput of the system drops by a factor of 2
for high loads. This is observed even though we are nowhere near the
network limits at this point. The measured outgoing throughput is
390217 ops/sec or 39M bytes/sec or 310M bits/sec which is well under
the expected 32Gbps limit.
The red, blue and green lines were measured with 24 RX buffers and
8, 32 and 64 TX buffers respectively.
The violet line was measured with 48 RX buffers and 8 TX
buffers. Notice that adding buffers to the pool on the receive side
allows the trasmit side to see a higher throughput - I do not
understand the reasons for this.
A set of further measurements are taken during the same experiment
and plotted on different graphs to aid understanding.
Latency Graph - Average number of buffers returned by pollCompletionQueue across different Buffer Pool sizes
Analysis
Summary - 3 empty buffers become available at a time under load.
Number of receive buffers also affects pollCompletionQueue().
This average does not include calls when no buffers were returned.
This is an average when non-zero buffers were returned by pollCompletionQueue().
The red, blue and green lines were measured with 24 RX buffers and
8, 32 and 64 TX buffers respectively.
The violet line was measured with 48 RX buffers and 8 TX buffers.
An interesting trend that appears to be independent of number of
buffers in the pool. There is a drop in the average at the same load
irrespective of buffer-pool.
Why does doubling the number of receive buffers affect the number of
empty transmit buffers returned ? Compare Red against Violet.
Look at the average number of buffers returned under high load.
It appears as if this number is around 3. We expect this number to be
1 buffer returned under load where empty buffers are returned as soon
as they are available. The higher number indicates that maybe buffers
are being returned in sets of 3. What is the reason for this behavior ?
Latency Graph - Time spent in pollCompletionQueue per read (average) across different Transmit Buffer Pool sizes
Analysis
Summary - pollCompletionQueue() (and hence getTransmitBuffer()) take
longer to run with increasing load. Note that pollCompletionQueue()
would be called multiple times until a succesful return - an empty
buffer from the pool.
Red/Blue lines represent 24 RX buffers and 8 TX buffers
Green/Violet lines represent 24 RX buffers and 32 TX buffers
Orange/Pink lines represent 24 RX buffers and 64 TX buffers
This a plot of measurements of time taken by the different functions
during the experiments.
Total time spent in pollCompletionQueue was tracked and then divided by the
number of read calls to calculate the average.
This tracks the curve of time spent within the getTransmitBuffer
call well. The difference between the two needs to be explained.
Latency Graph - Time spent in pollCompletionQueue per read (average) - fixed pool of buffers - comparing time taken by successful calls against calls that return 0
Analysis
This is the same latency curve as above restricted to the case where
the size of the buffer pool for TX buffers is 8.
The Red line represents avg time taken by the getTransmitBuffer() call.
The Blue line represents avg time taken across all the calls to
pollCompletionQueue()
The Green line represents the average time taken by calls to
pollCompletionQueue() calls that returned zero empty buffers.
The Violet line represents the average time taken by calls to
pollCompletionQueue() calls that returned non-zero empty buffers.
Note that time taken per successful call increased slightly with
load. Number of calls however increased with load resulting in overall
time taken by getTransmitBuffer() increasing.
